The Various Methods of Insulation

Posted on by 0 comment

Sound Lagging and Insulation

Sound lagging & acoustic lagging Melbourne is a process of overcoming the noise break-out during the insulation of pipes. If we look at power-generating industries they are always in need of an economical insulation and lagging system. These systems are to be installed correctly and they also need to be good in thermal efficiency. It is also been estimated that this industry would spend millions of dollars in repairing and installing the lagging and insulation.

Pipe Lagging Melbourne

If you have visited a steam generating facility then you would be aware that the average temperature is between 500F and 700 F.  However if your selection of an insulating material is based on thickness and thermal conductivity then you can use almost all type of insulation types as these have the same k-value. As far as k-value is concerned it has not shown any improvement in the last 30 years.

Pipe laggers

The pipe laggers are used to hold the heat within the pipes. It is actually a special type of insulation placed all over the water pipes. Since this method can keep the heat within the pipe it is used to save energy and even prevents the pipe from bursting and freezing.  In addition lagging also prevents condensation which can form on your cold pipes. Pipe lagging Melbourne devices are designed to overcome break-out of noise from pipes, valves and ductwork. This method is used in domestic, commercial and industrial buildings which makes it extraordinary.

Pipe Insulation

Pipe insulation is a method which is used to prevent loss of heat from the pipes.  It involves the use of plastic foamed insulation which is very commonly used to avoid the freezing of water supply pipes and it also helps in the reduction of heat loss from the heating pipes.

Sound insulation

Sound installation is done in order to prevent you from getting disturbed by the activity in the next room. This room can be upstairs or at the ground floor.  The construction has to be perfect which prevents the sound to move out of the room. Sound proofing means that there should be reduction of sound which can be achieved by using a good quality material or constructing a solid and strong structure. As far as sound installation is concerned there are two types of sound installation which are air borne sound installation and impact sound insulation.

Fyrewrap installation

Fyrewrap installation is a great method to help in the condition where you are losing heat from your domestic pipes. This method involves the application of Fyrewrap directly on the surface of the metal duct. This can be applied both in single and double layer. The best part of Fyrewrap is that it can be installed without any clearance between the wrap surface and the combustibles irrespective of the location of the wrap.

If you do not want to waste you should measure the Fyrewrap with care and apply before any fixture takes place.

The above methods are used to prevent the loss of heat from various energy generating processes.

 

Category: Uncategorized

How to Repair a Leaking Shower

Posted on by 0 comment

There are no binary perceptions about the fact that timely shower faucet repair can prevent a severe drain not just on your precious resources, but also on your hard-earned money. Leaking Showers

In order to successfully repair a shower faucet, it is important to get the facts concerning the faucet you will be repairing. However, the culprit is usually an old o-ring. When the o-ring needs to be replaced, this will cause a leaky shower faucet, and once it is replaced, your troubles will be over.

The o-ring is the rubber ring or gasket that is there to seal the shower cartridge. It will prevent all leaking, until it gets old and worn, or brittle over time from not enough use.

However, there are a number of reasons a shower faucet might leak, they include:

1. A loosed or worn packing

2. A worn washer or a worn valve seat

3. Worn o-rings

4. Accumulated sediments on disc type faucet

5. Worn seals on the disc type faucet

 

THE BASIC STEPS TO FOLLOW

Before you begin your shower faucet repair process, first turn off the water supply and as well open the valve to make sure all water is drained down.

Next, remove the faucet and check for mineral deposits which is usually lime. If there is any accumulated lime on the shower faucet assembly, you can soak the assembly parts in a white vinegar or purchase a solution designed specifically to dissolve lime.

Furthermore, unscrew the retaining nut with a shower stem socket tool which you can get at most hardware stores.

Also, remove the cartridge by just grasp the end with a pair of pliers and pull straight out. If the hole is too small, you can enlarge it with a screwdriver and hammer.

After the faucet is removed and soaked if necessary, check for caulking around the escutcheon plate. To remove the left behind caulking, simply use a plastic putty knife and always be careful not to damage the surface.

Next, peel off the o-ring by just slipping it from its grove. Keep the o-ring whole (do not cut) so that you can easily find an exact replacement at the hardware store. If you are not able to peel it off, you can pull it off with a screwdriver. Make sure that the o-ring grove is free of any lime deposits.

The next step is to apply silicone grease to the new o-ring. Slide the o-ring over the cartridge and fit it into the o-ring grove, then reassemble the faucet.

Also, don’t forget to reassemble the escutcheon plate and seal it with the caulking.

Lastly, turn the water back on and test for leaks. If it still continues to leak, repeat the above steps over again or contact the leaking shower repair experts at Melbourne.

 

Notwithstanding, listed below is the comprehensive list of the materials needed to fix a leaking shower faucet:

1. The O-ring

2. The cartridge replacement kit

3. A silicone grease

4. A white vinegar or lime dissolving solution

5. The caulking material.

Also, you’ll need a screwdriver, a plastic putty knife, shower stem socket kit, pliers, and a utility knife.

After completing your shower faucet repair and checking for leaks, your faucet should be good as new.

Category: Uncategorized